100W*2 OCL Two Channel Amplifier Board Module High Power Electronic DIY Kits

EUR 13,86 Sofort-Kaufen oder Preisvorschlag, Kostenloser Versand, 60-Tag Rücknahmen, eBay-Käuferschutz
Verkäufer: technicalaim ✉️ (36.454) 99.2%, Artikelstandort: ShenZhen, CN, Versand nach: WORLDWIDE, Artikelnummer: 402487563691 100W*2 OCL Two Channel Amplifier Board Module High Power Electronic DIY Kits.

Sophisticated product, please handle with care; quality first, credit upmost;  Your satisfaction is our pursuit;The strength of technology decide the quality of technology.                                         if  you have any problem,pls contact with us.

100W*2 OCL Two Channel Amplifier Board Module High Power Electronic DIY Kits

Features:
Fully separated components, four high-power triodes, two stereos, each with a power of up to 100W.
This power amplifier adopts the typical OCL circuit, which has the advantages of high stability, wide frequency response range and good fidelity. It is often used in high-fidelity sound reproduction equipment. This OCL stereo amplifier is suitable for use by a wide range of electronic enthusiasts and audiophiles.

First, the working principle of the circuit
As can be seen from the figure below, the output of the speaker and the amplifier is directly coupled, and the output capacitor for DC blocking is omitted. In order to make the DC potential of the output of the circuit zero volt, a positive and negative symmetrical power supply is used, and the differential amplifier input is used. And other measures. In Figure 1, vt i, vt2 are differential amplification input stages, vt3 is the excitation stage, and vt4~vt7 are composite complementary output stages. The audio signal is sent to the base of vt i through the coupling capacitors c 1 and ri. After amplification, it is output from the collector of vt i and sent to vt3 to further increase. The excitation signal of the collector output of vt3 pushes the power output stage vt4~ Vt7 works so that the amplified audio signal can drive the speaker to work.

To facilitate further analysis, Figure 1 can be simplified to the form of Figure 2. Vt4 and vt6 are combined to be equivalent to one npn transistor, and vt5 and vt7 are equivalent to one pnp transistor. It can be seen from the vt4, 6 and vt5, 7 of the circuit of Fig. 3 and the power supply filter capacitors c9, c10 that they are equivalent to a bridge. When vt4, 6, vt5, and 7 are identical, c9 and c10 are also identical, the bridge arms are balanced, and the speaker does not pass through. If the positive and negative power supplies are completely symmetrical, the output potential can be guaranteed to be 0V.

Since the circuits are all directly coupled, any changes in ambient temperature and component parameters will affect the potential at the output (point a, Figure 2). To this end, vt 1, vt2 constitute a differential amplifier to overcome the zero drift, DC negative feedback is also applied in the circuit, that is, the output is applied to the base of vt2 through r6, so that the potential of the output (point a) is zero. Volt. The feedback process is: a point potential ↑—ube2 ↑—ie2 ↑—ur4 ↑—ube l ↓一ic l↓一uc 1 ↑—ube3 ↓一ie2 ↓—ur7↓一ube4,6 ↓(ube5,7 ↑) A vt4, 6 internal resistance v (vt5, 7 internal resistance ↓) a point potential ↓. On the other hand, if the potential at point a is ↓, the potential at point a will be paralyzed by the opposite change process.

Second, the installation and production
The printed circuit diagram of this circuit is shown in Figure 3. It includes a two-way OCL power amplifier circuit and a DC power supply circuit. A heat sink is required between the body of the 4 high power tube 2N3055 and the printed circuit board, and is fixed by screws. The resistors are installed horizontally. The capacitors and triodes are installed vertically and close to the circuit board. The soldering requirements are firm and reliable. There are two jumpers on the circuit board, which can be soldered with iron wires.

Third, debugging
The power transformer used in this circuit needs to be prepared by itself. It adopts a center-tapped dual output transformer (AC: 1 5VX2), the power is not less than 40W, and is connected to the AC~ and the upper part of the printed circuit board. After being energized, it is generated at both ends of C9 and C10. With a DC voltage of ±18V, the voltage across the speaker is zero volts.

First adjust the current of the differential amplifiers vt l, vt2, in order to avoid the large current flowing through the power tube, first short the base of vt4, vt5 with a wire, so that vt4 ~ vt7 cut off. Then solder one end of the resistor r6 to the ground and solder it to ground. The total emitter current of the differential amplifier stage is determined by r4. The R4 is adjusted so that the total emitter current of vt 1 and vt2 is 1 mA. After the resistor r6 is restored, the voltage across the speaker should be o. If there is an offset, adjust r3.   Package Included:
1 x OCL Amplifier Board DIY Kit Shipping

1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.

2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.

3.All package need to wait 30 days ,Please take care it.Less than 30 days,we can't take a refund.

Feedback

1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.

2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly.

Payment

1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.

2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.

3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.

 

Return policy

1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.

2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.

3. Please include your eBay ID and item number with any email requests.

 

Contact us

1. If you have any questions, please feel free to email our service specialists.

2.Just contact us using the " Ask the seller a question" link on eBay.

3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.

100W*2 OCL Two Channel Amplifier Board Module High Power Electronic DIY Kits Features:
Fully separated components, four high-power triodes, two stereos, each with a power of up to 100W.
This power amplifier adopts the typical OCL circuit, which has the advantages of high stability, wide frequency response range and good fidelity. It is often used in high-fidelity sound reproduction equipment. This OCL stereo amplifier is suitable for use by a wide range of electronic enthusiasts and audiophiles.

First, the working principle of the circuit
As can be seen from the figure below, the output of the speaker and the amplifier is directly coupled, and the output capacitor for DC blocking is omitted. In order to make the DC potential of the output of the circuit zero volt, a positive and negative symmetrical power supply is used, and the differential amplifier input is used. And other measures. In Figure 1, vt i, vt2 are differential amplification input stages, vt3 is the excitation stage, and vt4~vt7 are composite complementary output stages. The audio signal is sent to the base of vt i through the coupling capacitors c 1 and ri. After amplification, it is output from the collector of vt i and sent to vt3 to further increase. The excitation signal of the collector output of vt3 pushes the power output stage vt4~ Vt7 works so that the amplified audio signal can drive the speaker to work.

To facilitate further analysis, Figure 1 can be simplified to the form of Figure 2. Vt4 and vt6 are combined to be equivalent to one npn transistor, and vt5 and vt7 are equivalent to one pnp transistor. It can be seen from the vt4, 6 and vt5, 7 of the circuit of Fig. 3 and the power supply filter capacitors c9, c10 that they are equivalent to a bridge. When vt4, 6, vt5, and 7 are identical, c9 and c10 are also identical, the bridge arms are balanced, and the speaker does not pass through. If the positive and negative power supplies are completely symmetrical, the output potential can be guaranteed to be 0V.

Since the circuits are all directly coupled, any changes in ambient temperature and component parameters will affect the potential at the output (point a, Figure 2). To this end, vt 1, vt2 constitute a differential amplifier to overcome the zero drift, DC negative feedback is also applied in the circuit, that is, the output is applied to the base of vt2 through r6, so that the potential of the output (point a) is zero. Volt. The feedback process is: a point potential ↑—ube2 ↑—ie2 ↑—ur4 ↑—ube l ↓一ic l↓一uc 1 ↑—ube3 ↓一ie2 ↓—ur7↓一ube4,6 ↓(ube5,7 ↑) A vt4, 6 internal resistance v (vt5, 7 internal resistance ↓) a point potential ↓. On the other hand, if the potential at point a is ↓, the potential at point a will be paralyzed by the opposite change process.

Second, the installation and production
The printed circuit diagram of this circuit is shown in Figure 3. It includes a two-way OCL power amplifier circuit and a DC power supply circuit. A heat sink is required between the body of the 4 high power tube 2N3055 and the printed circuit board, and is fixed by screws. The resistors are installed horizontally. The capacitors and triodes are installed vertically and close to the circuit board. The soldering requirements are firm and reliable. There are two jumpers on the circuit board, which can be soldered with iron wires.

Third, debugging
The power transformer used in this circuit needs to be prepared by itself. It adopts a center-tapped dual output transformer (AC: 1 5VX2), the power is not less than 40W, and is connected to the AC~ and the upper part of the printed circuit board. After being energized, it is generated at both ends of C9 and C10. With a DC voltage of ±18V, the voltage across the speaker is zero volts.

First adjust the current of the differential amplifiers vt l, vt2, in order to avoid the large current flowing through the power tube, first short the base of vt4, vt5 with a wire, so that vt4 ~ vt7 cut off. Then solder one end of the resistor r6 to the ground and solder it to ground. The total emitter current of the differential amplifier stage is determined by r4. The R4 is adjusted so that the total emitter current of vt 1 and vt2 is 1 mA. After the resistor r6 is restored, the voltage across the speaker should be o. If there is an offset, adjust r3.   Package Included:
1 x OCL Amplifier Board DIY Kit Shipping

1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.

2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.

3.All package need to wait 30 days ,Please take care it.Less than 30 days,we can't take a refund.

Feedback

1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.

2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly.

Payment

1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.

2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.

3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.

 

Return policy

1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.

2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.

3. Please include your eBay ID and item number with any email requests.

 

Contact us

1. If you have any questions, please feel free to email our service specialists.

2.Just contact us using the " Ask the seller a question" link on eBay.

3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.


Am 11.10.20 hat der Verkäufer die folgenden Angaben hinzugefügt:

  • Condition: Neu
  • Marke: Markenlos
  • Markenkompatibilität: Universal
  • Produktart: Verstärker-Bausatz
  • Brand: Unbranded
  • Type: DIY Amplifier Kit

PicClick Insights - 100W*2 OCL Two Channel Amplifier Board Module High Power Electronic DIY Kits PicClick Exklusiv

  •  Popularität - 70 Beobachter, 0.1 neue Beobachter pro Tag, 1.265 days for sale on eBay. Super hohe beobachtend. 46 verkauft, 10 verfügbar.
  •  Bestpreis -
  •  Verkäufer - 36.454+ artikel verkauft. 0.8% negativ bewertungen. Großer Verkäufer mit sehr gutem positivem Rückgespräch und über 50 Bewertungen.

Die Leute Mochten Auch PicClick Exklusiv